DT> @REPLY: 1:116/901.0 0d7a4410   
    DT> @MSGID: 1:132/505 50d856e4   
    DT> @PID: GED+386 1.1.4.7   
    DT> @CHRS: IBMPC 2   
      
    DT> Squish thinks that ASCII 95 is the correct character to use in the   
    DT> tear, that would explain why it's adding one even if there's a   
    DT> previous (ASCII 45) tear in the message, added buy GOldED+ - if   
    DT> Squish is looking for three 95 chars and what's there is 3 45   
    DT> chars.   
      
   FWIW: here's all your control lines above and below so you can see exactly   
   what is getting out here to the rest of the network ;)   
      
    DT> There's no GoldED+ tear in the messages I'm sending out because   
    DT> I've configured GoldED+ to not add one - I don't want to end up   
    DT> with two, which is what was happening when I was testing.   
      
   two tearlines, while not "pretty" is not bad, either... but your GoldED is   
   using the PID since you've turned off the tearline stuff... PIDs and tearlines   
   with text are a nono according to the PID/TID spec...   
      
    DT> Thanks for your help, I'll see what I can figure out.   
      
   might need the squish sources and apply some code fixing so it'll either   
   recognize the PID and add an empty tearline or it'll use the TIP instead and   
   have an empty tearline... then one might also add the option to specify   
   stripping the tearline since they are not required by the spec ;)   
      
    DT> Daniel   
      
    DT> ... Vermont USA: 18th-century charm, 19th-century conveniences    
      
    DT> ___ Squish/386 v1.11   
    DT>  - Origin: • Almost At The Top Of The Hill • Newfane, VT USA •   
    DT> (1:132/505)    
      
   the above modified automatically when quoted... the tearline is now three   
   underscores instead of dashes... the asterisk in the origin line is now a   
   single dash... my editor, TimED, does this automatically so that brain dead   
   tossers don't get confused...   
      
    DT> @EEN-BY: 10/1 11/201 331 18/0 19/33 34/999 103/105 109/500 112/0    
    DT> 114/487   
    DT> @EEN-BY: 116/18 116 901 123/0 52 57 140 500 789 880 1025 128/2 187   
    DT> @EEN-BY: 132/174 505 135/364 137/10 140/1 154/10 222/2 226/0 600 229/426   
    DT> @EEN-BY: 230/150 249/303 250/100 306 261/38 100 1406 1466 266/420   
    DT> @EEN-BY: 266/1413 267/155 280/1027 292/908 298/5 311/2 320/101 119   
    DT> @EEN-BY: 320/219 322/320 759 340/400 387/22 396/45 633/260 712/848   
    DT> @EEN-BY: 801/161 189 2320/105 303 3634/12 22 50 5030/1256   
    DT> @ATH: 132/505 174 320/119 261/38 123/500 3634/12   
      
   )\/(ark   
      
   ---    
    * Origin:  (1:3634/12.42)