MSGID: 1:154/110@fidonet.org 68aa6aff   
   REPLY: 54716.sync@1:103/705 2d104ae2   
   PID: GED+W64 1.1.5-b20250409   
   TID: SBBSecho 3.28-Win32 master/a43ca30ea Jun 18 2025 MSC 1942   
   BBSID: LIVEWIRE   
   TZUTC: -0500   
   CHRS: CP437 2   
   FORMAT: flowed   
      
   Hello Digital!   
      
   28 Feb 71 17:32, you wrote to me:   
      
    DM>   Re: Why New Install   
    DM>   By: RickV to Accession on Sat Aug 23 2025 02:40 pm   
      
    >>   
    >> Hello Accession!   
    >>   
    >> 28 Feb 71 14:28, you wrote to me:   
    >>   
    >>  Ac> Hey RickV!   
    >>   
    >>  Ac> On Sat, Aug 23 2025 09:54:32 -0500, you wrote:   
    >>   
    >>  >> On my Synchronet/Linux system, when I run the cfg It trys to   
    >> run a   
    >>  >> new installation and not my current setup. Why would this   
    >> happen?   
    >>  >> All my ini's in /crtl are intact. Is there something I can to   
    >> to   
    >>  >> repair this?   
    >>   
    >>  Ac> Sounds like when you try to run 'scfg' it doesn't know where   
    >> to look   
    >>  Ac> for those .ini files.   
    >>   
    >>  Ac> Try 'export SBBSCTRL=/path/to/sbbs/ctrl' before you run   
    >> 'scfg'.   
    >>   
    >>  Ac> See https://wiki.synchro.net/config:env for how to set it   
    >> properly so   
    >>  Ac> you don't have to manually type it every time.   
    >>   
    >> I have it set, but went back and set it again, run scfg and the   
    >> same "New Installation", so I have a problem, just not sure why?   
    >> BEEN fine for months now.. but?   
      
    DM> Are you configuration settings in tact (name of your BBS, etc.)? If   
    DM> so, then you're good to go. Just complete the config wizard and the   
    DM> "new install" flag will be turned off automatically.   
      
    DM> Didn't you migrate computers or OSes or something recently? It seems   
    DM> you've had a lot of problems since you did that and this is just one   
    DM> of them.   
    DM> --   
      
   They all looked good. I did migrate a few months ago, but it was working   
   normal up till today. I can't think of what I might have done, but I'm sure it   
   must have been something I did. I did recover it back, I do a back up every   
   night so I did a recovery of that VM and it work fine after that.   
      
   Thanks,   
   RickV   
      
      
   --- SBBSecho 3.28-Win32   
    * Origin: Live Wire BBS [livewirebbs.com:1025] (1:154/110)   
   SEEN-BY: 105/81 106/201 128/187 129/14 153/7715 154/110 218/700 226/30   
   SEEN-BY: 227/114 229/110 114 206 317 400 426 428 470 700 705 266/512   
   SEEN-BY: 291/111 320/219 322/757 342/200 396/45 460/58 633/280 712/848   
   SEEN-BY: 902/26 5075/35   
   PATH: 154/110 229/426