REPLY: 3:633/280@fidonet 5e9424ff   
   MSGID: 2:250/1@fidonet 5e95b58d   
   CHRS: UTF-8 2   
   TZUTC: 0100   
   TID: MBSE-FIDO 1.0.7.13 (GNU/Linux-x86_64)   
   Hello Stephen!   
      
   Monday April 13 2020 18:35, you wrote to All:   
      
      
    >    Hello everybody!   
      
    > I've just had a new node do a areafix request and the body of the   
    > netmail just has   
      
    > %+ALL   
      
    > in it, and the system reports that:   
      
      
    > Here is the result of your Areamgr request:   
      
    >  * Area %ALL not found.   
      
      
    > Reading the helpfile a "%+ALL" should work.   
      
      
    > Recomendations?   
      
      
   From share/int/macro/en/areamgr.help   
      
   -!-   
   In the body of the message to AreaMgr:   
      
   +    To connect to an echomail area   
   -    To disconnect from an echomail area   
   %+ALL          To connect to all echomail areas   
   %-ALL          To disconnect from all echomail areas   
   %+      To connect all echomail areas of a group   
   %-      To disconnect from all echomail areas of a group   
   %HELP          To request this help message   
   %LIST          To request a list of echomail areas available to you   
   %QUERY         To request a list of echomail areas for which you are active   
   %UNLINKED      To request a list of echomail areas available to you   
                  to which you are not already connected   
   %FLOW          To request a flow report of available areas   
   %STATUS        To request a status report for your system   
   %PAUSE         To temporary disconnect from the connected echomail areas   
   %RESUME        To reconnect the temporary disconnected echomail areas   
   %PWD=newpwd    To set a new AreaMgr and FileMgr password   
   %MSGS       To set max. number of messages to be rescanned   
   %RESCAN  To request messages from 'area' again   
   %NOTIFY=On/Off To switch the notify function on or off   
   [---]          Everything below the tearline is ignored   
   -!-   
      
   So  the line   
   %+ALL   
      
   Should work  - what do you have in log/manager.log  for the date time of his   
   request?   
      
      
   Out of interest has any one else had the same problems that I am suffering    
   from   
   when compiler mbse in that there are loads of warnings being issued during the   
   compile - see my previous post.   
      
      
      
   Vincent   
      
   --- Mageia Linux v7.1 X64/Mbse v1.0.7.13/GoldED+/LNX 1.1.5-b20180707   
    * Origin: Air Applewood, The Linux Gateway to the UK & Eire (2:250/1)   
   SEEN-BY: 1/120 123 14/5 6 15/0 18/0 200 19/36 90/1 103/705 106/201   
   SEEN-BY: 116/18 120/331 601 123/0 25 50 140 150 170 755 128/2 135/300   
   SEEN-BY: 153/757 7715 154/10 30 40 700 203/0 218/700 221/0 6 226/30   
   SEEN-BY: 227/114 201 400 229/101 426 452 1014 230/150 152 240/1120   
   SEEN-BY: 240/5832 249/206 317 400 250/1 261/38 100 266/512 267/155   
   SEEN-BY: 275/100 280/464 5003 282/1031 1056 288/100 291/100 111 292/854   
   SEEN-BY: 317/3 320/119 219 322/757 340/400 341/66 342/13 200 396/45   
   SEEN-BY: 423/120 633/280 640/1321 712/848 770/1 801/161 189 2320/105   
   SEEN-BY: 2452/250 3634/0 12 15 27 50 119 5020/1042   
   PATH: 250/1 261/38 3634/12 154/10 280/464 229/426