TZUTC: -0500   
   MSGID: 469.fidonet-ls_arrl@1:2320/33 28d02f83   
   PID: Synchronet 3.20a-Win32 master/52fa4b0ea May 18 2023 MSC 1929   
   TID: SBBSecho 3.20-Win32 master/52fa4b0ea May 18 2023 MSC 1929   
   BBSID: TBOLT   
   CHRS: ASCII 1   
   NOTE: The N0KFQ BBS is no more, due to the deaths of the Sysop, K.O. Higgs   
   (N0KFQ)(SK), and his wife, Billie (KB0WSA)(SK).   
      
   However, the basic format noted below should work with any amateur radio   
   satellite. Just substitute the callsigns and hierarchial addresses, as   
   noted.   
      
   Daryl, WX4QZ   
      
   ***   
      
               How To Send Packet Messages By Satellite   
               ========================================   
      
   From        : N0KFQ   
   To          : USERS   
   Type/status : BN   
   Date/time   : 13-Sep 09:46   
   BID (MID)   : 27233_N0KFQ   
   Message #   : 27233   
   Title       : +Messages by Satellite   
      
   (This message has been read 1   times today.)   
      
   The W0SL satellite gateway has been set up specifically to provide a fast   
   means of sending personal mail on foreign routes via the packet satellites.   
   No bulletins and no foreign NTS traffic will be forwarded.   
      
   You will need to format the message you wish to send in a particular way.   
   As an example, you want to send a message to Jim, 4X1AB, whose Home BBS is   
   4X1YZ. At your BBS prompt send your message to;   
      
    SP REQSAT @ W0SL                 [REQuest SATellite at W0SL]   
    Rig problems.                    [Enter the subject as normal]   
    SP 4X1AB @ 4X1YZ.ISR.MDLE        [Enter the REAL address as the FIRST   
    Hi Jim the rig has been....      [line of the message. A SPACE must exist   
    text text etc.....               [between SP and the first callsign.   
    /ex   
      
   Add the FULL HIERARCHICAL ADDRESS, as shown above, it is REQUIRED for the    
   correct routing of your message.  Don't forget the "SP".   
      
   So to sum up, at your BBS prompt enter;   
      
        SP REQSAT @ W0SL   
      
   when asked for the subject enter whatever you like, such as;   
      
        TNC problems again!!!   
      
   When asked for the Message the VERY FIRST LINE must contain the REAL   
   address, including the HIERARCHICAL ADDRESS, such as;   
      
        SP 4X1AB @ 4X1YZ.ISR.MDLE   
      
   Don't forget the "SP".  Do not put anything else on this first line!   
   Then on the following line, enter the rest of the message as you would   
   normally, ending with the usual;   
      
        /EX   
      
   When the message arrives at W0SL it will be automatically re-addressed   
   according to the first line of the message.  The subject you entered will   
   be the same and ALL the headers will remain, so anyone doing a SR reply   
   will have the reply sent back to the BBS you entered the message on.   
      
   N0KFQ  July 16, 2000   
      
   === End of messsage #27233 to USERS from N0KFQ ---   
   --- SBBSecho 3.20-Win32   
    * Origin: The Thunderbolt BBS - Little Rock, Arkansas (1:2320/33)   
   SEEN-BY: 1/19 123 15/0 16/0 19/37 90/1 105/81 106/201 116/17 18 123/10   
   SEEN-BY: 123/130 131 142/104 153/7715 154/10 30 40 50 700 203/0 218/700   
   SEEN-BY: 220/90 221/0 6 226/18 30 227/114 229/110 112 113 206 307   
   SEEN-BY: 229/317 426 428 470 664 700 240/1120 1200 1634 2100 5411   
   SEEN-BY: 240/5824 5832 5853 8001 8002 8005 266/512 280/5003 282/1038   
   SEEN-BY: 291/111 301/1 113 313/41 317/3 320/119 219 319 2119 322/0   
   SEEN-BY: 322/757 335/364 342/200 371/0 396/45 460/58 633/280 712/848   
   SEEN-BY: 2320/0 33 105 304 401 2454/119 3634/12 5020/1042   
   PATH: 2320/33 105 154/10 301/1 240/1120 5832 320/219 229/426