home bbs files messages ]

Just a sample of the Echomail archive

Cooperative anarchy at its finest, still active today. Darkrealms is the Zone 1 Hub.

   AUTOMOTIVE      Anything to do with cars      2,177 messages   

[   << oldest   |   < older   |   list   |   newer >   |   newest >>   ]

   Message 860 of 2,177   
   Roy Witt to Mark Hofmann   
   Odd rumble in Durango solved.   
   09 Apr 12 04:20:41   
   
   08 Apr 12 20:40, Mark Hofmann wrote to Roy Witt:   
      
      
      
    RW>> Pink is a South Texas special. Because of the very high temps around   
    RW>> here,   
    RW>> all summer long, it supposedly cools better than orange or green.   
    RW>>   
    RW>> AFAIK, Yellow is a Ford factory antifreeze...   
      
    MH> Around here, I have only seen the Yellow and Green.  I guess there   
    MH> also a few people that still get the red Dexcool.   
      
   The Dexcool in my Z28 was orange...hmmm, could be that it was more water   
   than Dexcool.   
      
    RW>> Tell him I have a factory sealed gallon of Dexcool I'll sell him,   
    RW>> cheap.   
      
    MH> I'm sure he woudn't be interested.   
      
   Neither am I, but yesterday I noticed that gallon of Dexcool while doing   
   some work in the garage.   
      
    MH> He told me when he bought the car, the first thing he did was drain   
    MH> out the Dexcool and put the yellow stuff in. I have seen Dexcool get   
    MH> all gummy in some systems, too.   
      
   I've never had a problem with it and the Z28 has never given me anything   
   to worry about in the cooling department. Early on, I replaced the 195   
   degree thermostat with a 180 and that was the only thing I've done to it   
   in the cooling department up until the coolant flush and change.   
      
    RW>> Crankcases are pressurized with compressed air/fuel mixture blowing   
    RW>> by worn or sloppy piston rings. This is inevitable in internal   
    RW>> combustion engines. This is why a PCV 'positive crankcase (vent)   
    RW>> valve' was invented. Before PCV came into vogue, there was the 'road   
    RW>> draft tube' venting blowby and oil to the underside of you car, the   
    RW>> road and atmosphere. Ford's flathead V8s and Y-block V8s were famous   
    RW>> - For Oiling Road Dirt - in the day of road draft tubes. All other   
    RW>> cars did this too, but none of them lended a name to it better than   
    RW>> FORD.   
      
    MH> What about value covers?  My old Malibu used to leak some oil there   
    MH> onto the exhaust manifold.   
      
   Chevys have been famous for that. The old cork type of gasket would shrink   
   with age and the 4 screws would come loose, allowing oil to seep under the   
   cover gasket. The rubber replacement gaskets were even worse, slipping out   
   from under the cover when they got a dose of oil. I tend to stick with the   
   old school cork gasket, glue it to the cover and let it set on flat   
   surface over-night with a weight on top. Then install without any glue on   
   the head side and tighten the cover screws down as evenly as possible,   
   starting with the bottom 2 and then the top 2 screws. 87 an newer I use   
   the same procedure, but begin tightening the 2 inner nuts and follow up   
   with the 2 outer nuts when installing.   
      
    MH>   Not much, but it was enough to make a mess.   
      
   My 55 Chevy had a 30-30 Duntov cam in it. Adjusting the valves (.03   
   intake and .03 exhaust} with the engine running and the covers off allowed   
   the oil to pump over the fenders. I found a set of rocker clips (still   
   have them today) that covered the oil hole in the rocker which kept the   
   oil in the engine, until it flooded the head and overflowed onto the   
   exhaust. I learned to do only one bank at a time, shut it down, clean it   
   up and re-install that cover before tackling the other bank of cyl.   
      
    RW>> Again, a blowby problem will force oil out of the rear seal.   
      
    MH> I have heard that if a PCV value gets really clogged it can cause   
    MH> that compression to get too high and blow some gaskets.   
      
   That it will. Rather than service a PCV, I just replace them periodically.   
      
      
                   R\%/itt   
      
      
     ... Only those who will risk going too far can possibly   
     ... find out how far one can go ~ TS Eliot   
      
      
   --- Twit(t) Filter v2.1 (C) 2000-10   
    * Origin: Roiz Flying \A/ Service * South Texas * USA * (1:387/22)   

[   << oldest   |   < older   |   list   |   newer >   |   newest >>   ]


(c) 1994,  bbs@darkrealms.ca